I have a Ryobi compact drill and noticed the reviews on the Ryobi drill bits are not so great.
I am thinking to get a different brand if possible.

The set that Ryobi makes is (Ryobi Speed Load Plus 17-Piece Titanium Drill Bit Set) from Home depot

I am looking for a do it all kind of set but will mostly be drilling into my walls which are some are stucco & some brick I also will be using on wood. Will not be doing metal so much not sure if a 4v drill can do that. I'm new to this so any advice helps. Thanks

My model is

Ryobi HP53LK TEK4 1/4 in. 4-Volt Screwdriver ( it turns into a drill )

Assembled Depth (in.) : 10.35 in
Assembled Height (in.) : 10.11 in
Assembled Width (in.) : 2.44 in
Batteries Included : Yes
Battery Type : 4V
Battery charge time (min.) : 60
CSA Listed : Yes
Charger Included : Yes
Chuck Size : 1/4 In.
Chuck Type : Hex
Clutch Setting : 24-position
Color Family : Green
Cordless Tool Type : Drill/Driver
Cordless/Corded : Cordless
Depth (in) : 1.968 in
ETL Listed : No
Height (in) : 7.086 in
Item Package Type : Cardboard Container
Item Weight : 2.21 lb
Manufacturer Warranty : 2 Years
Maximum speed (rpm) : 600
Power Tool Product Type : Cordless
Product Depth (in.) : 2.5 in
Product Height (in.) : 10 in
Product Weight (lb.) : 2.21
Product Width (in.) : 10.4 in
Reconditioned : No
Returnable : 90-Day
UL Listed : 1-UL Listed
Variable Speed : Yes
Voltage (volts) : 4 V
Width (in) : 9.055 in

I need to install a socket for another cigarette lighter socket. I need to know what size drill bit would fit a socket lighter. Please post ASAP. I have a GM fitting socket ready to go, wires are set and ready. I just need to know the exact size bit to use. Thanks

Hi,

I've got a Bosch PSR 1200 drill. I was given this and it has no instructions.

Can someone please tell me how I widen the place where I insert the drill bit (it has 3 gears in it, I believe it may be called the 'chuck'?) and then tighten it again around the drill bit please?

Thanks in advance,

Hal.

Wife has gotten a cast iron kettle pot and wants to put plants into it for our backyard garden. She has asked me to drill holes into the bottom of the kettle so water can drain out. So what type of drill bit can I use that won't disintegrate when I try to drill the holes?

I have a Frigidaire gas range that I am looking to convert back to natural from LP. Model#FGF355AWG.
Left Rear - 8k btu
Right Rear - 4.5k btu
Left Front - 8k btu
Right Front - 10k btu
Oven Burner - 16k btu

Instead of buying the new orifices I would like to know what size drill bit I need to use to adjust them.

What are the shank diameters of MegaBore Drill Bits?

Does the MegaBore drill bit require a specially designed shaft for MegaBore bits?

I have a 1/4" diameter extension (4.5 feet), and I want to know if this bit will fit without any other special MegaBore extensions.

http://www.lsdinc.com/content/product_details/22

I got an email response from LSD. It looks like I will need to get a 7/16" Connecting-Hole MegaBore Shaft, which is 1/4" in diameter, and then connect the MegaBore Shaft to the regular 1/4" flex extension.

Email Response:
"Hello,

The 7/16” Hex, is the standard size for similar bits.

Thanks

Customer Service Department

Labor Saving Devices,Inc."

I was trying to use an easy-out in a broke off bolt on my motorcycle and twisted off the easy-out also. What drill bit is hard enough to drill through the metal of the easy-out and where could I get this bit?

WTH!!
Why did the porsche engineers use alien wrench screws for the head of the engine. The last screw that i have stripped and am wondering is there any drill bit out there that wont go dull the second it touches this strong piece of German steel.
Esay out screw extractor does not work. If a drill bit can drill the screw how would a screw extractor do the job?

I have a 3/8 " drill. What size drill bits would work in that drill? Can I use a drill bit that is less than 3/8. Can I use a drill bit les than 3/8 up to 3/8. Would it work if I use a bigger drill bit like 1/2 inch?
What does it mean a drill si 3/8 is that measuring the circumfernce or diameter. Does 3/8 mean the maximum drill bit is 3/8

I understand how to attach the two that came with the drill. But I purchased a screwdriver and drilling set (Black and Decker) and there are all these different sizes of bits, but the ends are very skinny....way too small for my drill. I found a hex thingy-ma-jig in the kit that has the proper end to go into my drill. But, how the heck does the drill bit get attached to the hex? The bit end is very skinny. Now, the screwdriver bits fit just fine into the hex. What am I missing here?
Thanks for any help!
This is my first drill!!